Tags |
|
|
Links |
|
|
Member You - Car Audio Amplifier Info: Seriously Everything You'll Ever Need To Know
I saw a reference to the term "fat cat" as I was in the middle of doing some little bitsy thing on one of my sites, one of those that you know is not going to make you RICH, it's just a question of sending perhaps 20 visitors a month one way, instead of another.It then occurred to me that there's a metaphor in there somewhere.HOW do fat people get to be FAT?By eating huge portions?Yeahhhh .... sort of ... but that's not where it starts, that's more of an after effect.IT'S THE LITTLE BITSY THINGS THAT DO THE TRICK!A snack of cake here. A nibble of a few nuts there. A biscuit or two. A little glass of wine ... mmmmh, a small piece of cheese would go just perfectly with that .... Just a couple of extra chips won't hurt ...LOL!I don't know why this amuses me so, but the thing is that you can get "fat catting" using that same principle on your business operations.A tiny little link here ... a little article there ... a tasty little banner ... a bit of a download ... a teensy note to your mailing list ... you can hardly notice it at all ...And then you look around as a couple of years have passed, and WHOA!You're not a skinny starving newbie anymore, but have unnoticeably turned into an "internet fat cat"!HOW did that happen?!Haha!But I gu
HOW TO DETERMINE WHICH AMP IS BEST FOR YOUR SYSTEM:
How many channels is your system?
How to hook up those channels.
Features you want
Crossover:
Inputs:
speaker (hi level)
rca, pre-amp (lo level)
How many channels are you going to drive? We already discussed the ranges of stereo systems, so you need to determine how many speakers you're driving. Say you want to build an intermediate system with 6 speakers. You figure you want to amplify all 6 of those with a "real" amp. You can go a few routes: You can buy a 6 channel amp, or a 5 channel amp, and power your whole system. That makes life easy if you want to keep installation clean and simple. You could also power your speakers with multiple amps: One mono, one 4-channel, you could even use three stereo amps. If you want to get really fancy, you could bi-amp your component speakers, bringing your amp count to 3, 4, and 5 amps!
One way that you can get creative with your installation is through bridging. If you want to power 2 or more subs on a stereo amp, you can bridge it, or combine the two channels into one. From there, you can wire your subs in parallel or series to obtain the proper ohm load. It's an easy way to power multiple speakers on one amp.
To save money, you can always opt not to install an amp for the rear speakers. I often times just power them off of the head unit. If I am listening to music without rear passengers, I can just fade the head unit to the front, leaving me with the amplified front speakers.
Do you need an amp to have a crossover?
Crossovers come in handy when you are powering subwooers. Most amps can reproduce the entire range of human hearing. However, when we install subs, we only want them to reproduce bass. If the amp has a crossover, you ca
American obesity rates continues to rise. Obese individuals that have a BMI (Body Mass Index) of 40 or higher are continuing to sky rocket. "The proportion of people at the high end of the weight scale continues to increase at a brisk rate despite increased public attention on the risks of obesity and the increased use of drastic weight loss strategies, such as bariatric surgery," report author Roland Sturm, a RAND economist.It does not matter the health risks, Americans continue to gorge themselves on fat laden food. Fast food joints are increasing and healthy choices are dissipating. It is easy to place the blame on the individual. But, you do not have to look far to see another advertisment, for your favorite fast food resteraunt.The price of obesity is causing health care cost in America to soar. The U.S. Government should not close their eyes and wait for the problem to go away. It's an ever growing problem and the blame cannot rest entirely on the individual. Obesity can cause extreme health problems, such as, Type 2 diabetes, heart disease, strokes, sleep apnea, gall bladder disease and fatty liver disease.All of these diseases are the root cause for escalating U.S. health care costs. Corporations are finding themselves handcuffed. They want to provide insurance for their workers, but the cost of h
Amplifiers are devices that take a teeny tiny audio signal from a pre-amp, some power from your battery, and pass it on as a big big audio signal to drive speakers.
The most important piece of advice I can give to you is to buy lots of power. To get the cleanest sound, it is absolutely essential to buy as much power as you can afford.
Here are some terms that you'll need to know when evaluating car audio amplifiers.
Watt: A watt is a measurment of power. Power is the ability to do work. In the case of amplifiers, the work is to move a speaker. Amplifiers come in all power ranges, from 20 watts per channel up to thousands per channel. When it comes to amplifiers, watts are described two ways:
RMS: An amp's power rating might say: 75W RMS x 4 CH @ 4Ω 14.4V This means that the amp is capable of 75 watts into 4 channels with 4 ohm speakers, and 14.4V of voltage. This amp is capable of providing that power if all of those conditions are met at all times. The truth is, even if you design your system to meet all of those conditions, it will not at all times. Speakers' impedences (measured in ohms, or Ω) change constantly while operating. Amps don't necessarilly put out the same power all of the time either, for example when a bass track is playing versus a much quieter track.
WHEN BUYING AN AMP, LOOK AT IT'S POWER RATING AS A MARKER FOR YOUR AMP'S CAPABILITY RATHER THAN WHAT IS LIKELY TO PUT OUT AT ALL TIMES.
However, I must also say that an amp's RMS rating is the one piece of information to look for to determine an amp's power.
CEA Compliant Power Output: This is (hopefully) going to become the industry standard for determining an amp's power output. This allows you to accurately compare two amps to each other, because you know that they were tested under the same conditions. To know why this is a good thing, click here...
MAX: Right under an amp's RMS rating, you'll see an amp's "MAX" rating. It is often double the RMS rating. The MAX rating is pure junk. Never pay attention to the max rating because it only shows what the amp is capable of in a laboratory setting. That kind of environment cannot be reproduced in the auto, and therefore the rating is misleading. An amp's max rating is proably about 50% more than the RMS. Never buy an amp based on it's Max rating. Ok, and lastly, because this makes you look like a total jerk, never ever ever say your amp is a 1000 watt amp because it has a max 1000 watt sticker on it, and ESPECIALLY if you bought your amp at the swap meet. 1000 watt amps are BIG and HEAVY.
Anyway, in summation, never buy an amp based on it's MAX rating.
CEA Compliant Power: (CEA=Consumer Electronics Association) This spec (if your amplifier includes it) is a new rating. The goals of this rating are to give a useful reference for amp comparison. In the "bad old days", amp manufacturers could pretty much claim whatever power output they wanted without specifying the testing methods. The CEA rating changes that. The CEA compliant power output specifies what power output you can expect when the following criteria are met: 14.4V, 4 Ohm speaker load and 1% distortion. You can now fairly compare two amplifiers to each other because you know they were tested in the same manner. Make sense? No? OK, look at it this way: If an amp has a CEA compliant output power of 100 watts per channel, you know that the amp is essentially equal to another amp with the same CEA rating. HOWEVER, you cannot compare this amp to another amp that is rated at 100 watts/channel RMS.
I am a big fan of this rating. FINALLY, there is a uniform standard for amplifier power output ratings. If an amp doesn't include this spec, then the manufacturer is probably trying to hide something.
Bridging: Many stereo and 4 channel amps allow you to "bridge". What you do with bridging is combine two channels into one, or four channels into two. This allows you to allocate more power to a single speaker, like a subwoofer for example. This is a handy feature for someone who has a stereo amp lying around, but they want to use all of its power to drive a single speaker. There's nothing wrong with bridging, and is often used for subwoofers.
Crossover: Many amps have a simple crossover built in. Basically, it will be a switch that will have three positions: high pass, low pass, off. High pass basically allows all of the higher frequencies to pass. This is handy if the amp is powering tweeters and mids. The low pass allows only the lower frequencies to be reproduced. This is handy if the amp is powering a subwoofer. Off means that all frequencies will be sent to the speaker.
Bass Boost: Some amps have a circuit that when switched on gives a boost to your bass. It is not essential, and I usually don't use it in my own system.
Frequency Response: This specification tells you what frequencies that the amp responds to. Higher frequencies are treble, lower frequencies are bass. The human ear can perceive from 20hz to 20,000hz (aka 20khz). Most amps will reproduce this frequency band with ease. Some will go above and beyond. Don't worry about that because usually CDs don't contain data out of that range, and even if they did, you wouldn't hear it! Some people talk about harmonics, and I don't know if it's true or not. But whateva. Read about this debate elsewhere.
Channel: Amps have channels that basically tell you how many loads it is built to drive. Loads=speakers, so a two channel amp will power two speakers.
Classes:
Different amps have different designs that all achieve the same thing (amplifying a musical signal), but achieve this in different ways. The way in which the amplifier is designed is refered to as its "class". There are 4 major types of classes, and an occasional oddball. I don't really know the technical differences between them, but it doesn't matter. We're just installing amps, not designing them!
A - Very good sound quality, very inefficient, uses boatloads of power, and wastes most of it in the form of heat.
B - Good sound quality, moderately efficient, uses a lot of power, wastes about half of it in the form of heat. Some "crossover distortion" present
A/B - Combination of classes A and B. At low volumes, uses the class A portion of the amp. At higher volumes, uses the class B portion of the amp.
D - So-so sound quality (but reproduces bass very well), highly efficient, uses minimal power, wastes very little of it.
Other classes: Whatever. They exist. I don't know if they sound better. Your ears are the best judge.
THD: This stands for "total harmonic distortion", but the D is all you have to pay attention to. Obviously, the lower this number, the better. You don't want your amps producing distortion and sending it to your speakers! It causes noise and speaker damage. The experts say any THD rating below 0.1% is inaudible, meaning you can't perceive it. But remember that distortion travels through all components, and is amplified by each one. So, having a low distortion amp, and other high distortion items in your system will reproduce distortion.
S/N Ratio: A Measure of how an amplifier silences backround noise. This spec is measured in db, and the HIGHER the s/n ratio, the cleaner your sound.
Speaker Level Inputs: This feature allows you to connect the amp to your system through speaker wires (instead of RCA cables). This feature is handy if you're adding an amp to your factory stereo system.
Preamp Outputs: This feature allows you to connect an RCA cable to the amp to supply a second amp with the musical signal. This feature is handy if you want to add a second amp without running a cable all the way from your head unit to the amp. Also, it allows you to add an additional amp to a head unit that may have only one set of RCA pre-outs.
Remote bass control: This feature allows you to control the bass output of the amp without having to adjust it on the amp. You can mount the control wherever's clever, and adjust the bass remotely.
HOW TO DETERMINE WHICH AMP IS BEST FOR YOUR SYSTEM:
How many channels is your system?
How to hook up those channels.
Features you want
Crossover:
Inputs:
speaker (hi level)
rca, pre-amp (lo level)
How many channels are you going to drive? We already discussed the ranges of stereo systems, so you need to determine how many speakers you're driving. Say you want to build an intermediate system with 6 speakers. You figure you want to amplify all 6 of those with a "real" amp. You can go a few routes: You can buy a 6 channel amp, or a 5 channel amp, and power your whole system. That makes life easy if you want to keep installation clean and simple. You could also power your speakers with multiple amps: One mono, one 4-channel, you could even use three stereo amps. If you want to get really fancy, you could bi-amp your component speakers, bringing your amp count to 3, 4, and 5 amps!
One way that you can get creative with your installation is through bridging. If you want to power 2 or more subs on a stereo amp, you can bridge it, or combine the two channels into one. From there, you can wire your subs in parallel or series to obtain the proper ohm load. It's an easy way to power multiple speakers on one amp.
To save money, you can always opt not to install an amp for the rear speakers. I often times just power them off of the head unit. If I am listening to music without rear passengers, I can just fade the head unit to the front, leaving me with the amplified front speakers.
Do you need an amp to have a crossover?
Crossovers come in handy when you are powering subwooers. Most amps can reproduce the entire range of human hearing. However, when we install subs, we only want them to reproduce bass. If the amp has a crossover, you ca
About 25 years ago I began formulating pet foods at a time when the entire pet food industry seemed quagmire and focused on such things as protein and fat percentages without any real regard for ingredients. Since boot leather and soap could make a pet food with the "ideal" percentages, it was clear that analytical percentages do not end the story about pet food value. I was convinced then, as I am now, that a food can be no better than the ingredients of which it is composed. Since this ingredient idea has caught on in the pet food industry, it has taken on a commercial life that distorts and perverts the meaning of the underlying philosophy of food quality and proper feeding practices. Is health reducible to which ingredients a commercial product does or does not have? As contradictory as it may seem to what I have just said, no it is not. Here's why.AAFCO Approval The official Publication of the American Association of Feed Control Officials (AAFCO) gives wide latitude for ingredients that can be used in animal foods. As I have pointed out in my book, The Truth About Pet Foods, approved ingredients can include*: dehydrated garbage undried processed animal waste products polyethylene roughage replacement (plastic) hydrolyzed poultry feathers hydrolyzed hair hydrolyzed leather meal
Anyway, in summation, never buy an amp based on it's MAX rating.
CEA Compliant Power: (CEA=Consumer Electronics Association) This spec (if your amplifier includes it) is a new rating. The goals of this rating are to give a useful reference for amp comparison. In the "bad old days", amp manufacturers could pretty much claim whatever power output they wanted without specifying the testing methods. The CEA rating changes that. The CEA compliant power output specifies what power output you can expect when the following criteria are met: 14.4V, 4 Ohm speaker load and 1% distortion. You can now fairly compare two amplifiers to each other because you know they were tested in the same manner. Make sense? No? OK, look at it this way: If an amp has a CEA compliant output power of 100 watts per channel, you know that the amp is essentially equal to another amp with the same CEA rating. HOWEVER, you cannot compare this amp to another amp that is rated at 100 watts/channel RMS.
I am a big fan of this rating. FINALLY, there is a uniform standard for amplifier power output ratings. If an amp doesn't include this spec, then the manufacturer is probably trying to hide something.
Bridging: Many stereo and 4 channel amps allow you to "bridge". What you do with bridging is combine two channels into one, or four channels into two. This allows you to allocate more power to a single speaker, like a subwoofer for example. This is a handy feature for someone who has a stereo amp lying around, but they want to use all of its power to drive a single speaker. There's nothing wrong with bridging, and is often used for subwoofers.
Crossover: Many amps have a simple crossover built in. Basically, it will be a switch that will have three positions: high pass, low pass, off. High pass basically allows all of the higher frequencies to pass. This is handy if the amp is powering tweeters and mids. The low pass allows only the lower frequencies to be reproduced. This is handy if the amp is powering a subwoofer. Off means that all frequencies will be sent to the speaker.
Bass Boost: Some amps have a circuit that when switched on gives a boost to your bass. It is not essential, and I usually don't use it in my own system.
Frequency Response: This specification tells you what frequencies that the amp responds to. Higher frequencies are treble, lower frequencies are bass. The human ear can perceive from 20hz to 20,000hz (aka 20khz). Most amps will reproduce this frequency band with ease. Some will go above and beyond. Don't worry about that because usually CDs don't contain data out of that range, and even if they did, you wouldn't hear it! Some people talk about harmonics, and I don't know if it's true or not. But whateva. Read about this debate elsewhere.
Channel: Amps have channels that basically tell you how many loads it is built to drive. Loads=speakers, so a two channel amp will power two speakers.
Classes:
Different amps have different designs that all achieve the same thing (amplifying a musical signal), but achieve this in different ways. The way in which the amplifier is designed is refered to as its "class". There are 4 major types of classes, and an occasional oddball. I don't really know the technical differences between them, but it doesn't matter. We're just installing amps, not designing them!
A - Very good sound quality, very inefficient, uses boatloads of power, and wastes most of it in the form of heat.
B - Good sound quality, moderately efficient, uses a lot of power, wastes about half of it in the form of heat. Some "crossover distortion" present
A/B - Combination of classes A and B. At low volumes, uses the class A portion of the amp. At higher volumes, uses the class B portion of the amp.
D - So-so sound quality (but reproduces bass very well), highly efficient, uses minimal power, wastes very little of it.
Other classes: Whatever. They exist. I don't know if they sound better. Your ears are the best judge.
THD: This stands for "total harmonic distortion", but the D is all you have to pay attention to. Obviously, the lower this number, the better. You don't want your amps producing distortion and sending it to your speakers! It causes noise and speaker damage. The experts say any THD rating below 0.1% is inaudible, meaning you can't perceive it. But remember that distortion travels through all components, and is amplified by each one. So, having a low distortion amp, and other high distortion items in your system will reproduce distortion.
S/N Ratio: A Measure of how an amplifier silences backround noise. This spec is measured in db, and the HIGHER the s/n ratio, the cleaner your sound.
Speaker Level Inputs: This feature allows you to connect the amp to your system through speaker wires (instead of RCA cables). This feature is handy if you're adding an amp to your factory stereo system.
Preamp Outputs: This feature allows you to connect an RCA cable to the amp to supply a second amp with the musical signal. This feature is handy if you want to add a second amp without running a cable all the way from your head unit to the amp. Also, it allows you to add an additional amp to a head unit that may have only one set of RCA pre-outs.
Remote bass control: This feature allows you to control the bass output of the amp without having to adjust it on the amp. You can mount the control wherever's clever, and adjust the bass remotely.
HOW TO DETERMINE WHICH AMP IS BEST FOR YOUR SYSTEM:
How many channels is your system?
How to hook up those channels.
Features you want
Crossover:
Inputs:
speaker (hi level)
rca, pre-amp (lo level)
How many channels are you going to drive? We already discussed the ranges of stereo systems, so you need to determine how many speakers you're driving. Say you want to build an intermediate system with 6 speakers. You figure you want to amplify all 6 of those with a "real" amp. You can go a few routes: You can buy a 6 channel amp, or a 5 channel amp, and power your whole system. That makes life easy if you want to keep installation clean and simple. You could also power your speakers with multiple amps: One mono, one 4-channel, you could even use three stereo amps. If you want to get really fancy, you could bi-amp your component speakers, bringing your amp count to 3, 4, and 5 amps!
One way that you can get creative with your installation is through bridging. If you want to power 2 or more subs on a stereo amp, you can bridge it, or combine the two channels into one. From there, you can wire your subs in parallel or series to obtain the proper ohm load. It's an easy way to power multiple speakers on one amp.
To save money, you can always opt not to install an amp for the rear speakers. I often times just power them off of the head unit. If I am listening to music without rear passengers, I can just fade the head unit to the front, leaving me with the amplified front speakers.
Do you need an amp to have a crossover?
Crossovers come in handy when you are powering subwooers. Most amps can reproduce the entire range of human hearing. However, when we install subs, we only want them to reproduce bass. If the amp has a crossover, you ca
With all the worries about tainted pet food, you may ask yourself if there's another option to give your cat or dog the nutrition it needs. A better option? Making food yourself for your pet.For owners that want the best for their pets, cooking the pet food 'from scratch' can be a fine option. While not as easy as store bought food, it is a great way to better control what your cat or dog is eating, and improve their nutrition.Humans, cats, dogs,, and every other animal have specific nutritional requirements. And while store bought dog and cat food is simple to use, it might not be the best in all cases.Many dog and cat foods are not made for the pet's requirements first, but expense first. This means using cheaper and poorer quality ingredients. For example, many cat or dog foods use vegetable matter for filler (like the wheat gluten involved in the pet food crisis of early 2007). While this does lower costs, it is not the natural protein dogs and cats are made for - meat.Although it is possible for dogs can go without real meat, cats can't. Various specific nutrients are required by cats, and are most easily found in meat. So, unless you are prepared to do a serious research into nutritional needs, and carefully monitor your pet's eating habits, you'll need to ensure there's sufficient meat in their
Crossover: Many amps have a simple crossover built in. Basically, it will be a switch that will have three positions: high pass, low pass, off. High pass basically allows all of the higher frequencies to pass. This is handy if the amp is powering tweeters and mids. The low pass allows only the lower frequencies to be reproduced. This is handy if the amp is powering a subwoofer. Off means that all frequencies will be sent to the speaker.
Bass Boost: Some amps have a circuit that when switched on gives a boost to your bass. It is not essential, and I usually don't use it in my own system.
Frequency Response: This specification tells you what frequencies that the amp responds to. Higher frequencies are treble, lower frequencies are bass. The human ear can perceive from 20hz to 20,000hz (aka 20khz). Most amps will reproduce this frequency band with ease. Some will go above and beyond. Don't worry about that because usually CDs don't contain data out of that range, and even if they did, you wouldn't hear it! Some people talk about harmonics, and I don't know if it's true or not. But whateva. Read about this debate elsewhere.
Channel: Amps have channels that basically tell you how many loads it is built to drive. Loads=speakers, so a two channel amp will power two speakers.
Classes:
Different amps have different designs that all achieve the same thing (amplifying a musical signal), but achieve this in different ways. The way in which the amplifier is designed is refered to as its "class". There are 4 major types of classes, and an occasional oddball. I don't really know the technical differences between them, but it doesn't matter. We're just installing amps, not designing them!
A - Very good sound quality, very inefficient, uses boatloads of power, and wastes most of it in the form of heat.
B - Good sound quality, moderately efficient, uses a lot of power, wastes about half of it in the form of heat. Some "crossover distortion" present
A/B - Combination of classes A and B. At low volumes, uses the class A portion of the amp. At higher volumes, uses the class B portion of the amp.
D - So-so sound quality (but reproduces bass very well), highly efficient, uses minimal power, wastes very little of it.
Other classes: Whatever. They exist. I don't know if they sound better. Your ears are the best judge.
THD: This stands for "total harmonic distortion", but the D is all you have to pay attention to. Obviously, the lower this number, the better. You don't want your amps producing distortion and sending it to your speakers! It causes noise and speaker damage. The experts say any THD rating below 0.1% is inaudible, meaning you can't perceive it. But remember that distortion travels through all components, and is amplified by each one. So, having a low distortion amp, and other high distortion items in your system will reproduce distortion.
S/N Ratio: A Measure of how an amplifier silences backround noise. This spec is measured in db, and the HIGHER the s/n ratio, the cleaner your sound.
Speaker Level Inputs: This feature allows you to connect the amp to your system through speaker wires (instead of RCA cables). This feature is handy if you're adding an amp to your factory stereo system.
Preamp Outputs: This feature allows you to connect an RCA cable to the amp to supply a second amp with the musical signal. This feature is handy if you want to add a second amp without running a cable all the way from your head unit to the amp. Also, it allows you to add an additional amp to a head unit that may have only one set of RCA pre-outs.
Remote bass control: This feature allows you to control the bass output of the amp without having to adjust it on the amp. You can mount the control wherever's clever, and adjust the bass remotely.
HOW TO DETERMINE WHICH AMP IS BEST FOR YOUR SYSTEM:
How many channels is your system?
How to hook up those channels.
Features you want
Crossover:
Inputs:
speaker (hi level)
rca, pre-amp (lo level)
How many channels are you going to drive? We already discussed the ranges of stereo systems, so you need to determine how many speakers you're driving. Say you want to build an intermediate system with 6 speakers. You figure you want to amplify all 6 of those with a "real" amp. You can go a few routes: You can buy a 6 channel amp, or a 5 channel amp, and power your whole system. That makes life easy if you want to keep installation clean and simple. You could also power your speakers with multiple amps: One mono, one 4-channel, you could even use three stereo amps. If you want to get really fancy, you could bi-amp your component speakers, bringing your amp count to 3, 4, and 5 amps!
One way that you can get creative with your installation is through bridging. If you want to power 2 or more subs on a stereo amp, you can bridge it, or combine the two channels into one. From there, you can wire your subs in parallel or series to obtain the proper ohm load. It's an easy way to power multiple speakers on one amp.
To save money, you can always opt not to install an amp for the rear speakers. I often times just power them off of the head unit. If I am listening to music without rear passengers, I can just fade the head unit to the front, leaving me with the amplified front speakers.
Do you need an amp to have a crossover?
Crossovers come in handy when you are powering subwooers. Most amps can reproduce the entire range of human hearing. However, when we install subs, we only want them to reproduce bass. If the amp has a crossover, you ca
Over the years of originating home equity loans, I have formulated some key theories about what consumers want and benefit from with their second mortgages. My theories are based on feed back from my clients, and noted observations over the last few years. With the real estate boom in the rear-view mirror, it is important to take a moment and consider the driving forces of home equity lending. Let us take a few moments and explore the core benefits of person taking out a secure loan with their home's equity.1. Quicker Access to Cash: Bottom line, people want cash available when they need it, whether it for purchasing a car, a second home or refinancing their loans. This explains the increased popularity for home equity credit lines.2. Consolidate Debt: American like to spend with credit, and credit card debt can hinder finances quickly. Fortunately homeowners have figured out how effective debt consolidation can be as demonstrated with many home equity loans. All too often I have seen people abuse credit and it gets them into trouble. No big screen TV is worth the headaches from over-extended debt.3. Affordable Monthly Payments: Before recommending a specific home equity loan to my clients, I want to make sure that they can afford the payment liabilities for their new venture. I have learned how impor
A - Very good sound quality, very inefficient, uses boatloads of power, and wastes most of it in the form of heat.
B - Good sound quality, moderately efficient, uses a lot of power, wastes about half of it in the form of heat. Some "crossover distortion" present
A/B - Combination of classes A and B. At low volumes, uses the class A portion of the amp. At higher volumes, uses the class B portion of the amp.
D - So-so sound quality (but reproduces bass very well), highly efficient, uses minimal power, wastes very little of it.
Other classes: Whatever. They exist. I don't know if they sound better. Your ears are the best judge.
THD: This stands for "total harmonic distortion", but the D is all you have to pay attention to. Obviously, the lower this number, the better. You don't want your amps producing distortion and sending it to your speakers! It causes noise and speaker damage. The experts say any THD rating below 0.1% is inaudible, meaning you can't perceive it. But remember that distortion travels through all components, and is amplified by each one. So, having a low distortion amp, and other high distortion items in your system will reproduce distortion.
S/N Ratio: A Measure of how an amplifier silences backround noise. This spec is measured in db, and the HIGHER the s/n ratio, the cleaner your sound.
Speaker Level Inputs: This feature allows you to connect the amp to your system through speaker wires (instead of RCA cables). This feature is handy if you're adding an amp to your factory stereo system.
Preamp Outputs: This feature allows you to connect an RCA cable to the amp to supply a second amp with the musical signal. This feature is handy if you want to add a second amp without running a cable all the way from your head unit to the amp. Also, it allows you to add an additional amp to a head unit that may have only one set of RCA pre-outs.
Remote bass control: This feature allows you to control the bass output of the amp without having to adjust it on the amp. You can mount the control wherever's clever, and adjust the bass remotely.
HOW TO DETERMINE WHICH AMP IS BEST FOR YOUR SYSTEM:
How many channels is your system?
How to hook up those channels.
Features you want
Crossover:
Inputs:
speaker (hi level)
rca, pre-amp (lo level)
How many channels are you going to drive? We already discussed the ranges of stereo systems, so you need to determine how many speakers you're driving. Say you want to build an intermediate system with 6 speakers. You figure you want to amplify all 6 of those with a "real" amp. You can go a few routes: You can buy a 6 channel amp, or a 5 channel amp, and power your whole system. That makes life easy if you want to keep installation clean and simple. You could also power your speakers with multiple amps: One mono, one 4-channel, you could even use three stereo amps. If you want to get really fancy, you could bi-amp your component speakers, bringing your amp count to 3, 4, and 5 amps!
One way that you can get creative with your installation is through bridging. If you want to power 2 or more subs on a stereo amp, you can bridge it, or combine the two channels into one. From there, you can wire your subs in parallel or series to obtain the proper ohm load. It's an easy way to power multiple speakers on one amp.
To save money, you can always opt not to install an amp for the rear speakers. I often times just power them off of the head unit. If I am listening to music without rear passengers, I can just fade the head unit to the front, leaving me with the amplified front speakers.
Do you need an amp to have a crossover?
Crossovers come in handy when you are powering subwooers. Most amps can reproduce the entire range of human hearing. However, when we install subs, we only want them to reproduce bass. If the amp has a crossover, you ca
There are many men that want to make a woman laugh when they are around each other. This is a good way to make things more comfortable and to ease the tension between yourself and the woman you like. This will help both of you feel good in each other's company and it will make it easier to be around each other.Be sure that you are being a little silly and giving your best when it comes to making them laugh. If you can learn how to make a woman laugh, you will be able to make friends with more women!1. Jokes are a great choice to make a woman laugh.This is a good second way to make a woman smile. You should think about the jokes that you are telling them. Be careful and do not go over board with the jokes that you tell. You want to be careful because you do not want to offend your girl.2. Be you.You will be surprised at what you can do with your own personality. Do not be afraid to be whom you are and you will be surprised at what will happen. You should not be afraid to do the things that you always do. You want to feel comfortable and be who you are with each other. You will be amazed at the fun that you will have because you are going to be able to express who you are and not worry about hiding anything from her. The laughs are sure to come when can feel comfortable with you and who you are.llows you to control the bass output of the amp without having to adjust it on the amp. You can mount the control wherever's clever, and adjust the bass remotely.
HOW TO DETERMINE WHICH AMP IS BEST FOR YOUR SYSTEM:
How many channels is your system?
How to hook up those channels.
Features you want
Crossover:
Inputs:
speaker (hi level)
rca, pre-amp (lo level)
How many channels are you going to drive? We already discussed the ranges of stereo systems, so you need to determine how many speakers you're driving. Say you want to build an intermediate system with 6 speakers. You figure you want to amplify all 6 of those with a "real" amp. You can go a few routes: You can buy a 6 channel amp, or a 5 channel amp, and power your whole system. That makes life easy if you want to keep installation clean and simple. You could also power your speakers with multiple amps: One mono, one 4-channel, you could even use three stereo amps. If you want to get really fancy, you could bi-amp your component speakers, bringing your amp count to 3, 4, and 5 amps!
One way that you can get creative with your installation is through bridging. If you want to power 2 or more subs on a stereo amp, you can bridge it, or combine the two channels into one. From there, you can wire your subs in parallel or series to obtain the proper ohm load. It's an easy way to power multiple speakers on one amp.
To save money, you can always opt not to install an amp for the rear speakers. I often times just power them off of the head unit. If I am listening to music without rear passengers, I can just fade the head unit to the front, leaving me with the amplified front speakers.
Do you need an amp to have a crossover?
Crossovers come in handy when you are powering subwooers. Most amps can reproduce the entire range of human hearing. However, when we install subs, we only want them to reproduce bass. If the amp has a crossover, you can turn it on, and essentially tell the amp to only send bass to the subwoofers. Since subs can only reproduce bass, why have the amp waste energy sending the subwoofers frequecies it can't reproduce? LUNACY I TELL YA!
Inputs
speaker: These are called high-level inputs because the signal is already highly amplified. Get an amp with high-level inputs if you are integrating an amp with a factory head unit.
rca: These are called low-level inputs because the signal is not highly amplified. These inputs are RCA style, and are preferred because they produce lower noise. This is the best option if you are using an aftermarket head unit.
So, now you're really educated about amps. Don't worry. You can thank us later!
-Honest AEB
HTTP = HTML link (for blogs, profiles,phorums):
<a href="http://www.memberyou.net/article/387466/memberyou-Car-Audio-Amplifier-Info-Seriously-Everything-Youll-Ever-Need-To-Know.html">Car Audio Amplifier Info: Seriously Everything You'll Ever Need To Know</a>
BB link (for phorums):
[url=http://www.memberyou.net/article/387466/memberyou-Car-Audio-Amplifier-Info-Seriously-Everything-Youll-Ever-Need-To-Know.html]Car Audio Amplifier Info: Seriously Everything You'll Ever Need To Know[/url]
Related Articles:
What is the Difference Between an Unsecured Personal Loan and a Secured Personal Loan?
Cable Customers Defect to Dish Network
Bookmark it:
|